- This topic has 10 replies, 1 voice, and was last updated 7 years, 9 months ago by .
- I have traktor pro 2 installed and my hercules e2 controller works fine with it, all controls are fine but no sounds played through traktor play.
Under Audio setup i have the following settings:
Audio device: ASIO4ALL v2
Sample rate: 24000Hz
Latency: 512Then under the ‘Built in soundcard’ bit i have ASIO4ALL selected again. The only other choice being something called” Conexant 20561 smartaudio ( (Wassapi) (Shared mode))”I have no idea what to do with input & output routing, but have had no luck with just guessing. could really use some help people. if you need any more info, let me know. thanksIt has been used for quite a long time to correct slightly off-pitch voice recordings, and it’s pretty good at that — most Auto-Tune use you will most likely not hear or detect.However, recently it’s also been used to correct way off-pitch recordings, and it has two negative effects when used like that — it makes the singer’s voice sound distorted, which sounds bad (unless it’s your goal, and in these cases it isn’t), and it shows that the singer isn’t even consistently capable of approximately hitting the notes. Antarestech.com What is Autotune?Auto-Tune is a program that measures and adjusts the pitch of a recording. Download free autotune software.On Audio Setup, select “ASIO4ALL” for audio device. Then, on Output Routing, select “Internal” for mixing mode, on Out Master select 1: Front Left, then 2: Front Right. Output Monitor should be 3: Back Left, then 4: Back Right.Degenerate, post: 21893, member: 2367 wrote: Alvin, in output routing the only options available for anything under the output routing tab is, “HD Audio digital out 1” and “HD Audio digital out 2”. Oh and im using a hercules e2 mixer so i’d need to use external mixer right? cheers manSo I’ve checked your controller the Hercules E2, and learned that it doesn’t have a built-in soundcard. And, the computer that you are connecting to is using a Digital-Out interface, which means your ordinary 3.5mm will not work with it. You will need a S/PDIF is a digital audio interconnect to RCA cable to be able to connect it to an external mixer or speakers.Try using Conexant 20561 smartaudio ( (Wassapi) (Shared mode)) as your audio setup and use “internal” in your output routing select “anything” that is available on your drop down list and see if any sound is produced in your computer.If it still doesn’t work, then your computer’s soundcard doesn’t support external audio routing, you may need to buy a DJ soundcard like one of these: http://www.digitaldjtips.com/2010/11/6-budget-dj-sound-cards/Degenerate, post: 21893, member: 2367 wrote: Alvin, in output routing the only options available for anything under the output routing tab is, “HD Audio digital out 1” and “HD Audio digital out 2”. Oh and im using a hercules e2 mixer so i’d need to use external mixer right? cheers manSo I’ve checked your controller the Hercules E2, and learned that it doesn’t have a built-in soundcard. And, the computer that you are connecting to is using a Digital-Out interface, which means your ordinary 3.5mm will not work with it. Serum crack for mac. You will need a S/PDIF is a digital audio interconnect to RCA cable to be able to connect it to an external mixer or speakers.Try using Conexant 20561 smartaudio ( (Wassapi) (Shared mode)) as your audio setup and use “internal” in your output routing select “anything” that is available on your drop down list and see if any sound is produced in your computer.If it still doesn’t work, then your computer’s soundcard doesn’t support external audio routing, you may need to buy a DJ soundcard like one of these: http://www.digitaldjtips.com/2010/11/6-budget-dj-sound-cards/Degenerate, post: 21893, member: 2367 wrote: Alvin, in output routing the only options available for anything under the output routing tab is, “HD Audio digital out 1” and “HD Audio digital out 2”. Oh and im using a hercules e2 mixer so i’d need to use external mixer right? cheers manSo I’ve checked your controller the Hercules E2, and learned that it doesn’t have a built-in soundcard. And, the computer that you are connecting to is using a Digital-Out interface, which means your ordinary 3.5mm will not work with it. You will need a S/PDIF is a digital audio interconnect to RCA cable to be able to connect it to an external mixer or speakers.Try using Conexant 20561 smartaudio ( (Wassapi) (Shared mode)) as your audio setup and use “internal” in your output routing select “anything” that is available on your drop down list and see if any sound is produced in your computer.If it still doesn’t work, then your computer’s soundcard doesn’t support external audio routing, you may need to buy a DJ soundcard like one of these: http://www.digitaldjtips.com/2010/11/6-budget-dj-sound-cards/3D 5.1 soundcards will work as long as you have two separate outputs. But, if you want to connect it to high-powered mixers and speakers, then I recommend buying a DJ soundcard from numark or native instruments. That way there would be no distortion if you pump up the volume. - Posts
No Sound Traktor Scratch Pro Download
No Sound Traktor Scratch Program
- The forum ‘DJing Software’ is closed to new topics and replies.
Traktor Scratch Download
Oct 03, 2010 Traktor Scratch Pro Everytime i try to start my Tracktor scratch pro, it loads the collection list and then it freezes and and i get the following message. This application has requested the Runtime to terminate it in an unusual way. Traktor scratch pro 2 free download - Traktor Pro, Traktor Pro, Scratch, and many more programs. Graphic Design Software Digital Photo Software MP3 & Audio Software. Traktor scratch pro.